WiRES-II Ver.
3.301
Log Message Table
|
Call Start No.XXXX |
A "Connect" request has been sent to node ID: XXXX. |
Call Start No.XXXX (SRG:#) |
An SRG "Connect" request has been sent to SRG node
XXXX (SRG#), (where # is the numeral 0-9 according to your node's
SRG list). |
In-Call from No.XXXX |
An incoming Connect request has been received from
node ID: XXXX. |
In-Call from No.XXXX (SRG:#) |
An incoming SRG Connect request has been received
from node ID: XXXX (SRG#), (where # is the numeral 0-9 according
to your node's SRG list. If a call comes from a node not on your
SRG list, the SRG ID number will be shown as an "X" here.) |
Connected to XXXX. |
A connection has been established with node ID: XXXX. |
end-key detected .. Hangup |
A disconnection request has been detected. |
Conference End. |
The disconnection process has been completed. |
MCU Call-Type[#] |
An SRG/FRG Group Call to Group "#" (# = A-D) was
initiated from your node. |
MCU-Call Type[#] from [XXXX] |
An incoming SRG/FRG Group Call to Group "#" (# =
A-D) was received from node XXXX. |
Call Change Start(SRG:#) |
During an SRG Group Call, an individual call to SRG
node "#" was placed (# = 0-9). |
Round QSO Room [####] Member ...
xxxxxx(####),xxxxxx(####) |
Round QSO Room [####] ... Room is empty
You are connected to Room XXXX, and nodes XXXXXX (####) and XXXXXX
(####). . .
are signed in to that room.
If nobody else is currently signed in into this
room besides your node, Room is empty" will appear. |
XXXXXX(####) IN. |
Node XXXXXX (####) has just entered the Round Table
QSO Room. |
XXXXXX(####) OUT. |
Node XXXXXX (####) has just left the Round Table
QSO Room. |
DO NOT CONNECT TO ROUND QSO ROOM
No.#### (Call Failed (code=04)) |
While "Round QSO Room Connection" was set to "Off
(Reject)," a connection request to the QSO Room was nonetheless
sent (and the connection was therefore not executed). |
Outside Call In Round QSO from
No.XXXX |
During operation in a Round Table QSO Room, an
outside call from FRG node XXXX was received. |
Outside Call In Round QSO from
No.XXXX(SRG:#) |
During operation in a Round Table QSO Room, an outside
call from SRG node XXXX (SRG #) was received (where # is the numeral
0-9 according to your node's SRG list. If a call comes from a node
not on your SRG list, the SRG ID number will be shown as an "X" here.) |
Outside MCU Call In Round QSO from
No.XXXX |
During Round Table QSO Room operation, an incoming
Group call was received from node ID: XXXX. |
Connect Request From XXXX |
A connection request came in from node ID: XXXX,
but it could not be executed because your node is already connected
to another node. |
call to Rejected ID_No[XXXX] (Call
Failed (code=02)) |
A connection request to a "Rejected ID" node ID:
XXXX was attempted (the command was not executed). |
call from Rejected ID_No[XXXX] |
A connection request from a "Rejected ID" node ID:XXXX
was received, and rejected. |
Group Call From (XXXX). Reject |
A Group Call connection request from a "Rejected
ID" node ID:XXXX was received, and rejected. |
return to room XXXX last ## count. |
An automatic connection to the Resident Round Table
QSO Room (ID XXXX) was accomplished.
The last "Return Counter" count number is listed,
for reference. |
return to room XXXX count over. |
The number of retries for Return to Resident Round
Table QSO Room exceeded the specified count. Reconnection was aborted. |
TX Timeout(over 3min). |
Transmission in excess of three minutes was detected,
and the TX Timeout was invoked.
(After three minutes, audio from the offending
node is automatically cut off.) |
*Monitor* Connected (xxx.xxx.xxx.xxx) |
A connection has been established to the remote PC
running the Remote Monitor Software(wiresmon.exe), and remote control
is being exercised.
((xxx.xxx.xxx.xxx) is the IP Address of the remote
PC connected to your node.) |
*Monitor* Disconnected (xxx.xxx.xxx.xxx) |
The remote PC has disconnected from your node ((xxx.xxx.xxx.xxx)
is the IP Address of the remote PC previously connected to your
node.) |
Browser connected from [ xxxxx
] IP:xxx.xxx.xxx.xxx |
A Web Browser is accessing your node from the remote
PC.
([xxxxx]: Information about the remote Browser)
((xxx.xxx.xxx.xxx) is the IP Address of the remote
PC connected to your node.) |
*Monitor* Voice ON (xxx.xxx.xxx.xxx) |
The remote PC is performing audio monitoring on your
node via the wiresmon.exe software.
((xxx.xxx.xxx.xxx) is the IP Address of the remote PC connected to your
node.) |
*Monitor* Voice OFF (xxx.xxx.xxx.xxx) |
The remote PC has ended audio monitoring on your
node via the wiresmon.exe software.
((xxx.xxx.xxx.xxx) is the IP Address of the remote
PC previously monitoring your node's audio.) |
*Monitor* ON AIR LOCK (xxx.xxx.xxx.xxx) |
The remote PC has engaged the ON AIR LOCK function
to inhibit transmission.
((xxx.xxx.xxx.xxx) is the IP Address of the remote
PC controlling your node.) |
*Monitor* ON AIR UNLOCK (xxx.xxx.xxx.xxx) |
The remote PC has engaged the ON AIR UNLOCK command,
to relinquish the inhibition of transmission.
((xxx.xxx.xxx.xxx) is the IP Address of the remote
PC previously controlling your node.) |
*localhost* ON AIR LOCK |
The ON AIR LOCK command has been executed locally
on your node's PC. |
*localhost* ON AIR UNLOCK |
The ON AIR UNLOCK command has been executed locally
on your node's PC. |
*localhost* ON AIR LOCK (Plugin) |
The ON AIR LOCK function has been engaged locally
on your node's PC via plug-in software. |
*localhost* ON AIR UNLOCK (Plugin) |
The ON AIR UNLOCK command has been executed locally
on your PC via plug-in software. |
COM:# Invalid Port No or Port was
already open |
A COM Port specification problem has been detected;
either there is no communication because the wrong COM Port was
selected, or that COM Port is already in use. |
Socket Connection Canceled [] Code=0
(Call Failed (code=09)) |
The connection request to another node was denied.
(The other node may be attempting a connection
to a different node, your node may be "Rejected," etc. |
Socket Communication timeOut..Hangup |
A time-out occurred while attempting to connect to
another node. the connection attempt was aborted. |
No Answer from called PC. (Call
Failed (code=11)) |
There was no response from the node to which a connection
attempt was sent. |
No Entry On ILS Server. (Call Failed
(code=03)) |
The ID number you sent a connection request to is
for a node not currently communicating with the host server, or
the ID you sent is not a valid ID on the WiRES system. |